- Industrial Grade Monitors
- Industrial Computer Backplanes
- PCI Express Backplanes
- Wireless Antenna
- PC_Boards
- CPU Cards
- Digital Signage
- FLAT PANEL DISPLAY TECHNOLOGY
- Vehicle mount computer
- Industrial Keyboards
- Industrial Communication
- Power Over Ethernet POE Switch
- Data Acquisition Systems
- Remote I-O Modules
- Communication Cards
- Ethernet Networking Switches
- IP Surveillance
- AC to DC Converters
- DC to DC Converter
- Switching Mode Power Supply
- DIN Rail Power Supply
- Power Supply System
- DC to AC Power Inverter
- Industrial Tablet PC'S
- Kiosk Solutions
- Factory And Office Automation
- Ethernet based modules
- CAN BUS Modules
- 15" WORKSTATION
DIN Rail Power Supply
We are an eminent name, which is engaged in offering DIN Rail Power Supply to the clients. The offered range of DIN rail power supplies is manufactured utilizing high grade raw material and advanced machinery in strict compliance with the industry laid norms and standards. This range includes MDR Series Power Supply, SDR Series Power Supply, WDR Series Power Supply and many more items. Additionally, the offered range of DIN rail power supplies is known for its shock and vibration resistance. Products that encompass this range are suitably mentioned
N/1 Redundant SMPS
Main Features
- Input : 195V - 230V AC, 50Hz
- Output : 30V/67A
- Line Regulation : 0.2% (60mV)
- Load Regulation : 1% (300mV from 10% to 100% load change measured on sense terminal
- Ripple &Noise : 0.5% (150mV Pk - Pk when measured with shortest probe lead length and 0.1uF/63V ceramic capacitor paralleled with 100uF/63V electrolytic capacitor across the probe tip.
- Efficiency : Better than 80%
- Power Factor : 0.9
- Indication : Power ON, DC OK, C/L, I/P U/V, I/P O/V, O/T
- Output Voltage Adj. : + 2V by front panel Vadj pot
- Current Limit (CC type) : 70~72A
- Output Over Voltage : 33V to 35V (Check at 10% load. (trip type) mains recycling required to restart SMPS after removing fault)
- Input Under Voltage : (Auto Recovery Type) To be checked at 10% load. Output shuts OFF when input voltage is falls down below 185vac.
- Input Over Voltage : (Auto Recovery Type) To be checked at 10% load. Output shuts OFF when input voltage goes beyond 264vac.
- Over Temperature : 900c + 50c (Factory Test only)
- Transient Response : Output should recover within 10ms for 50% step load change.
- TTL ON / OFF : 0 - OFF; 1 - ON (if required)
- 1O/P Current Monitoring : Scale : 70A = 10V, 67A = 9.57 (2%)
- Operating Temperature: High : 550C Operating. Derating 2.5 % per degree C
- beyond 500C output current is58A.(Unit is in OFF condition to be switched ON for last 1/2 hour to take the reading), Low : - 10 % Operating. (Unit is in OFF condition to be switched ON for last 1/2 Hr
- EMI / EMC : Will meet STD461
DIN Rail Power Supply
Main Features
- PWR-40-24 (MEAN WELL/ MDR-40-24)
- Universal AC input / Full range, DC input
- Protections : Short circuit / Overload / Over voltage
- Cooling by free air convection
- For installation on DIN rail TS-35/7.5 or 15
- NEC class 2 / LPS compliant (12V, 24V, 48V only)
- LED indicator for power on
- DC OK relay contact
- No load power consumption<0.75W
- 100% full load burn-in test
- PWR-60-24 (MEAN WELL / MDR-60-24)
- Universal AC input / Full range, DC input
- Protections : Short circuit / Overload / Over voltage
- Cooling by free air convection
- For installation on DIN rail TS-35/7.5 or 15
- NEC class 2 / LPS compliant (12V, 24V, 48V only)
- LED indicator for power on
- DC OK relay contact
- No load power consumption<0.75W
- 100% full load burn-in test
